In regards to a few closed forums, I wish to rekindle a topic in regards to Flic buttons on an iHost SonOff Hub. [image] node-red-contrib-flic-buttons A Node-RED node to inject events from flic buttons [image] iHost (SonOff) - Docker - Node Red A…

Reviewing this topic, I do not have a raspberry pi , but I do have a Flic LR2 hub that allows my HomeKit to work. All 5 of my buttons have the ability through a HomeKit bridge to run scenes or turn on and off my HomeKit devices. The Flic LR2 hub has an ip address and this SDK interface to run javasc…

So the device now says "connected", does that mean it is working ? I don't know ! However, I assume there has to be someone who does knows what is going on ?? Otherwise, why would they invest the time in creating two contributions, one 3 years ago, almost 4. ... And one over 8 years ago ??? I'm pre…

Not sure if I am replying to the topic above or below the script. But I was only able to remove the pallet install by removing node red completely. I also had to blow away the directory I created. Reinstalled Node-red , then added the pallets in order. 0.1.5 , then 1.1.1. Creating an account at the…

Hold on. You have a flic hub, this hub takes care of interacting with the flic buttons. The nodes you are referring to exist to interact with the buttons directly, without a hub, however: The fliclib-linux-hci daemon is a piece of software that acts similarly as a hub - you do not need this, beca…

So with 1.1.1 installed originally , I could not install 0.1.5 pallet add-on due to a conflict error. But without 0.1.5 pallet add-on I got a connection closed (error). Now by Installing 0.1.5 after deleting the folder on the SD card completely , enabled me to re-install both. However even before al…

We need to see the output of the debug. [image]

Upon further reply I will remove HCI 0.1.5 Addon from the node-red pallet, but for now attempted with the prior images to show a message counts of has not changed. The count is not happening, like it does so easily with the ihost SonOff to NS Panel SonOff handling its native devices (supported). Al…

The count is not happening Why do you need the count ? Node-red is based on message input and message output You need to determine what your flic buttons produce in terms of messages: see screenshot above. Connect it to a debug node, press the button and show the output in the debug window. Th…

ok I will review, see you tomorrow , LOL. .. Oh this is good stuff !

Just thought message data is more info than a simple message count. If I could get the data to increment once like I did with meross I would have said whoo hoo. Even if the data was wrong, incorrect, in error or registering as white noise. And : I do not know how to manipulate message data. Okay I…

Node-RED

Node-RED Forum

Flic - iHost Hub by SonOff

Share Your Projects

bakman2 23 May 2024 15:47 16

We need to see the output of the debug.

Topic		Replies	Views
SonOff iHost Hub Share Your Projects docker	2	223	17 May 2024
Interesting Sonoff device iHost Hardware docker	18	859	23 May 2024
How to get a Flic button to work with docker and a Pi3 General	4	361	29 July 2022
Reolink doorbell finally supports webhooks Share Your Projects doorbell	83	2797	10 April 2025
SIEMENS IOT 2000 - Node - Red ("simatic_iot2000", node) Industrial	48	2177	19 October 2022

Copyright OpenJS Foundation and Node-RED contributors. All rights reserved. The OpenJS Foundation has registered trademarks and uses trademarks. For a list of trademarks of the OpenJS Foundation, please see our Trademark Policy and Trademark List. Trademarks and logos not indicated on the list of OpenJS Foundation trademarks are trademarks™ or registered® trademarks of their respective holders. Use of them does not imply any affiliation with or endorsement by them.

Flic - iHost Hub by SonOff

Related topics